產品詳情

所在位置: 首頁> 產品目錄> 芬蘭noptel激光測距傳感器>

Noptel遠距離激光測距傳感器

產品名稱：Noptel遠距離激光測距傳感器
產品型號：LRX-25A
產品廠商：芬蘭noptel
產品文檔：

你添加了1件商品查看購物車

簡單介紹

Noptel遠距離激光測距傳感器 LRX-25A 湖北Noptel遠距離激光測距傳感器 LRX-25A

Noptel遠距離激光測距傳感器

的詳細介紹

Noptel遠距離激光測距傳感器 LRX-25A 湖北Noptel遠距離激光測距傳感器 LRX-25A

Technical specifificaons

The product requires export license. Pictures are referential. Specifications are subject to change without notice. Doc.:M43332BE

Performance Characteriscs Unit LRX-25A Note

Laser safety class - 1 Eye safe

Wavelength μm 1.5

Measurement range m 50 - 32 000

Measurement range

Standard target

m 10 000

Target size 2.3 x 2.3 m, visibility 15 km, target re-

flflecvity 30%, detecon probability >90%

Exncon rao dB 41.0

Large target @ 500 m, visibility 23 km, target reflflec-

vity 85%

Measurement me s 0.7 / 1.7 Typical / Max. performance measurement two

mes in ten seconds due to eye-safety

Connuous measurement rates Hz

1, 4, 10, 20,

100, 200

With reduced measurement ranges

Precision m 0.5 - 1.5 Depending on the distance and target reflflecvity

Beam divergence mrad 0.35

False detecon rate % < 1

Target discriminaon m < 30 Depending on the received signal level

Range gang resoluon m 1

Operang temperature °C -32 - +60

Storage temperature °C -40 - +71

Mechanical characteriscs Unit LRX-25A Note

Size (L/W/H) mm 88 x 53 x 37

Weight g 136

Alignment retenon mrad 0.2 Within operang temperature range

Alignment pointer nm 635 Laser Class 1

IP Protecon - N/A

Electrical characteriscs Unit LRX-25A Note

Serial interface - RS422 Connector type: Molex 53261-1071

Supply voltage V 7 - 30

Start-up me ms < 50

Power consumpon

during measurement

W < 4

Power consumpon

in Stand-by mode

W < 0.2

Unit can be completely shut down by external sig

nal to further minimize power consumpon

This document describes mechanical, optical, electrical and software interface of the

following Noptel LRX family modules:

? LRX-20A

? LRX-25A

? LRX-42A

Figure 1. LRX-20A and LRX-25A

Figure 2. LRX-42ADocument number

OS43418IE

Document nam

1.2.1 Class 1 modules

The LRX is eye-safe in every measurement mode.

The system which uses Class 1 LRX module shall have labelling according IEC 60825-

1:2014 as follows:

Text borders and symbols are recommended to be black on a yellow background, but for

Class 1 this color combination need not be used.

The labels shall be durable, permanently affixed, legible, and clearly visible during

operation, maintenance or service, according to their purpose.

If the size or design of the product makes labelling impractical, the label shall be included

with the user information or on the package.

Direct printing or engraving of equivalent labels on the laser product or panels is

acceptable.

Table 4: Molex connector pinout

pin # IN/OUT Description

1 IN RS-422 RX+ (or UART TXD) *1

2 IN RS-422 RX- (or RS-232 RX or UART RXD) *1

3 GND RS-422 GND

4 OUT RS-422 TX+ *1

5 OUT RS-422 TX- (or RS-232 TX) *1

6 GND Case/Supply ground *2

7 & 8 IN Supply voltage input (6.5 - 30V). Reverse voltage protected. See Table 5

for power consumption.

9 GND Case/Supply ground *2

10 IN Shutdown when pulled down <0.5V, Power On when > 1.1V(internal 100

kΩ pull up)

*1 The default interface is RS-422. Serial interface option must be defined during ordering.

*2 Isolation of the case from the electrical ground is possible. Isolation option must be defined in the order!

Table 5: Typical power consumption of the LRX-20A, LRX-25A & LRX-42A.

Operation Total [W]

Measure 3.7

Optional Pointer 0.9

Standby 0.2

1Document number

OS43418IE

Document name

Interface Control Document

Version

2.33

Page nr.

8 / 17

3 Serial communication protocol

This chapter describes the main command frames of laser range finder. Notice that all

commands described in earlier ICD document versions are still supported.

Default baud rate is 115200 bps (no parity, 8 data bits, 1 stop bit). Default electrical

interface is RS-422. RS-232 and UART are options. Serial transfer speed can be changed

by the user.

After about 50 ms from the power on the device sends a string “LRX x.x.x” where “x.x.x”

is the firmware version (e.g. 1.5.3). After the string the device is ready to take commands.

標題：

內容：

聯系人：

聯系電話：

Email：

公司名稱：

聯系地址：

注：1.可以使用快捷鍵Alt+S或Ctrl+Enter發送信息!

2.如有必要,請您留下您的詳細聯系方式!

鄂公網安備 42010502000348號